TAP.LAN from PCINFO

TITLE EAJIN001E Invalid Drive Specification, C,D, and E are valid

Explanation: When prompted for the drive on which to install TAP, a drive
other then C,D, or E was entered. TAP can only be installed on drive
C,D, or E.

Action: Enter C,D, or E.
******************************************************************
TITLE EAJIN002E Invalid Path Specification

Explanation: When prompted for the subdirectory on which to install TAP,
either the path specification was typed incorrectly, or it contains too many
subdirectory names.

The TAP installation program uses the DOS "Make Directory" function to
create
the subdirectory in which to install TAP.

Action: Enter the path specification again. For information about
subdirectories, see the DOS User' Guide.
******************************************************************
TITLE EAJIN003E Could not find source file:file_name

Explanation: The installation program did not find the file displayed
in the message. The wrong IBM Token-Ring 16/4 Trace and Performance
Diskette
is inserted in the default drive.

Action: Insert the correct diskette.
******************************************************************
TITLE EAJIN004E Open failed on target file

Explanation: The disk is full. The Trace and Performance programs
cannot be
installed.

Action: Return to DOS and erase files on the disk that are not needed.
Start
the installation program again.
******************************************************************
TITLE EAJIN005E Write Error disk may be full

Explanation: There is not enough room on the disk to install any more
files.

Action: Return to DOS and erase files on the disk that are not needed.
Start
the installation program again.
******************************************************************
TITLE EAJME060E Command line too long

Explanation: The file specification is more than 128 characters; the path
specification is too long.

Action: Make sure that the path specification and the file name together
do not exceed 128 characters. Move the file to a different subdirectory, if
necessary.
******************************************************************
TITLE EAJME100E Help Error

Explanation: Either the HELP.COM is not in the same subdirectory as the
TAP.EXE program, the /DOC directory does not exist, or there are no help
files in the /DOC subdirectory.

Action: Run the installation program again.
******************************************************************
TITLE EAJME102E TRACE could not be loaded

Explanation: The Trace Facility could not be loaded. Either there is too
much memory in a VDISK , or the TRACE.EXE program is not in the same
subdirectory as the TAP.EXE program.

Action: If the TRACE.EXE program is in the correct subdirectory, release
memory. Otherwise, run the installation program again.
******************************************************************
TITLE EAJME103E RTAP could not be loaded

Explanation: The Trace Analysis Facility (RTAP) could not be loaded.
Either
there is too much memory in a VDISK, or RTAP.EXE program is not in the same
subdirectory as the TAP.EXE program.

Action: If the RTAP.EXE program is in the correct subdirectory, release
memory.
Otherwise, run the installation program again.
******************************************************************
TITLE EAJME104E PERF could not be loaded

Explanation: The Performance Facility (PERF) could not be loaded. Either
there is too much memory in a VDISK, or the PERF.EXE program is not in the
same subdirectory as the TAP.EXE program.

Action: If the PERF.EXE program is in the correct subdirectory, release
memory.
Otherwise, run the installation program again.
******************************************************************
TITLE EAJME106E LOCN could not be loaded

Explanation: The Traffic Matrix Facility (LCON) could not be loaded.
Either
there is too much memory in a VDISK, or the LCON.EXE program is not in the
same subdirectory as the TAP.EXE program.

Action: If the LCON.EXE program is in the correct subdirectory, release
memory.
Otherwise, run the installation program again.
******************************************************************
TITLE EAJME107E LCAF could not be loaded

Explanation: The Traffic Matrix Analysis Facility (LCAF) could not be
loaded.
Either there is too much memory in a VDISK, or the LCAF.EXE program is
not in
the same subdirectory as the TAP.EXE program.

Action: If the LCAF.EXE program is in the correct subdirectory, release
memory.
Otherwise, run the installation program again.
******************************************************************
TITLE EAJME110E Trace file name must have an extension or TR*

Explanation: A trace file name was entered that does have an extention
beginning with the letters TR. If the trace file extension was changed, the
file cannot be used.

Action: If the file extension was entered incorrectly, enter it again and
continue. Otherwise, return to DOS and change the file name using the
correct
extension. Start the Trace and Performance program and try the operation
again.
******************************************************************
TITLE EAJME111E Performance file name must have an extension of CT*

Explanation: A performance file name was entered that doesn't have an
extension
extension beginning with the letter CT. If the performance file
extension was
changed, the file cannot be used.

Action: If the file extension was entered incorrectly, enter it again and
continue. Otherwise, return to DOS and change the file name using the
correct
extension. Start the Trace and Performance program and try the operation
again.
******************************************************************
TITLE EAJME112E Traffic file name must have an extension of LC*

Explanation: A traffic file extension was entered that does not begin with
the letters LC*. If the traffic file extension was changed, the file cannot
be used.

Action: If the file extension was entered incorrectly, enter it again and
continue. Otherwise, return to DOS and change the file name using the
correct
extension. Start the Trace and Performance program and try the operation
again.
******************************************************************
TITLE EAJME113E No file found meeting the specifications

Explanation: There are no files of this type in the current subdirectory.

Action: If there are files of this type in a different subdirectory, press
F2=DIR again and change the path specification in the command that is
displayed
on the panel.
******************************************************************
TITLE EAJME300E File name may not be CON

Explanation: An attempt was made to create a file named "CON." CON cannot
be used as a file name.

Action: Enter a different file name.
******************************************************************
TITLE EAJME900E Not enough memory to provide directory function

Explanation: There is not enough memory to process a directory request.

Action: Return to DOS, and make more memory available to the Trace and
Performance facilities. Start the Trace and Performance program and try the
operation again.
******************************************************************
TITLE EAJTR002E Invalid address or synonym

Explanation: Either an address is not valid, or a synonym is not
recognized.

Action: If an address is specified, make sure that it consists of valid
hexadecimal characters. If a synonym is specified, make sure that a synonym
file has been specified, and that the file contains the synonym that was
entered.
******************************************************************
TITLE EAJTR100E Help Error

Explanation: Either the HELP.COM is not in the same subdirectory as the
TAP.EXE program, the /DOC directory does not exist, or there are no help
files in the /DOC subdirectory.

Action: Run the installation program again.
******************************************************************
TITLE EAJTR101E Must specify file name

Explanation: You pressed ENTER before entering a file name, and a file name
is required for this operation.

Action: Enter a file name and press ENTER.
******************************************************************
TITLE EAJTR111E Unable to open parameter save file

Explanation: Either there is no room on the disk to save the parameter
file, or the file already exists and cannot be erased. Normally, when
you use
an existing file name to save new parameters, the Trace Facility
overwrites the
file on the disk. However, if the existing file is either damaged or write-
protect, the save parameter funcition fails.

Action: First, enter a different file name. If the error occurs again,
it is
likely that your disk is full. Return to DOS and erase files from the disk
that are not needed. Start the Trace and Performance program and try the
operation again.
******************************************************************
TITLE EAJTR112E Unable to open trace file

TAP.LAN from PCINFO

Action: Correct the value in the bit selection field.
******************************************************************
TITLE EAJRA158E Fixed search offset field is invalid.

Explanation: The fixed search offset field is not a decimal number, and a
decimal number is required.

Action: Enter a hexadecimal value.
******************************************************************
TITLE EAJRA159E Source SAP field is invalid.

Explanation: The source SAP field is not hexadecimal value, and a
hexadecimal
value is required.

Action: Enter a hexadecimal value.
******************************************************************
TITLE EAJRA160E Destination SAP field is invalid.

Explanation: The destination SAP field is not a hexadecimal value, and
a hexadecimal value is required.

Action: Enter a hexadecimal value.
******************************************************************
TITLE EAJRA161E Invalid frame or routing field length.

Explanation: The trace file is damaged. It is possible that some or all of
the data in the file cannot be analyzed.

Action: If you cannot obtain needed data from the file, run the trace
again.
If the problem continues, call the IBM Support Cneter.
******************************************************************
TITLE EAJRA162E File operation error.

Explanation: The trace file is damaged. It is possible that some or all
of the data in the file cannot be analyzed.

Action: If you cannot obtain neeeded data from the file, run the trace
again.
If the problem continues, call the IBM Support Center.
******************************************************************
TITLE EAJRA163E No frames found matching search conditions.

Explanation: There are no frames in the trace file that match the search
criteria. Search conditions are "ANDed" (combined), so frames that do not
match every search parameter are ignored.

Action: Either press F8=Reset Search Parameters to return to the default
search parameters (all Frames), or press F6=Search and enter different
search parameters. When you enter fewer search parameters, more frames
are found.
******************************************************************
TITLE EAJRA213E Invalid address or synonym.

Explanation: Either an address is not valid, or a synonym is not
recognized.

Action: If an address is specified, make sure that it consists of valid
hexadecimal characters. If a synonym is specified, make sure that a synonym
file has been specified, and that the file contains the synonym that was
entered.
******************************************************************
TITLE EAJRA215E All destination addresses are filled.

Explanation: An attempt was made to select more than 10 destination
addresses
from the synonym file. Only 10 source addresses can be selected.

Action: Do not select more than 10 addresses.
******************************************************************
TITLE EAJRA216E All source addresses are filled.

Explanation: An attempt was made to select more than 10 source
addresses from
the synonym file. Only 10 sourece addresses can be selected.

Action: Do not select more than 10 address.
******************************************************************
TITLE EAJRA300E File name may not be CON.

Explanation: An attempt was made to create a file named "CON." CON cannot
be used as a file name.

Action: Enter a different file name.
******************************************************************
TITLE EAJRA301E Configuration error xx.

Explanation: This is an internal error.

Action: Call the IBM Support Center.
******************************************************************
TITLE EAJRA900E Not enough memory to provide directory function.

Explanation: Data from the requested search required more memory than
available.

Action: Be more specific in your search parameters.
******************************************************************
TITLE EAJRA903E Not enough memory to read in the frame(s).

Explanation: The computer does not have enough memory to copy the entire
frame.

Action: Use filters to reduce the size of the frames that are captured,
or increase the amount of memory available to the Trace Facility.
******************************************************************
TITLE EAJRA909E Memory Allocation Failure.

Explanation: There is not enough memory for the Trace Analysis Facility.

Action: Return to DOS, stop all terminate/stay resident programs, and
remove
them for DOS memory. Start the Trace Analysis Facility again; if more
memory
is needed, start the Trace Analysis Facility using the RTAP Commands (do not
type in TAP). See Appendix D, "Using Commands to Start the Trace and
Performance Facilities" on page D-1, in your IBM Token-Ring Network 16/4
Trace and Performance Program User's Guide, for more information.
******************************************************************
TITLE EAJPF002E Invalid address or synonym.

Explanation: Either an address is invalid, or a synonym is not recognized.

Action: If an address is specified, ensure that it consists of valid
hexadecimal characters. If a synonym is specified, make sure that a
synonym file has been specified, and that the file contains the synonym
that was entered.
******************************************************************
TITLE EAJPF100E Help Error.

Explanation: Either the HELP.COM is not in the same subdirectory as the
TAP.EXE
program, the \DOC directory does not exist, or there are no help files
in the
\DOC subdirectory.

Action: Run the installation program again.
******************************************************************
TITLE EAJPF101E Must specify file name.

Explanation: You pressed ENTER before entering a file name, and a file name
is required for this operation.

Action: Enter a file name and press ENTER.
******************************************************************
TITLE EAJPF111E Unable to open parameter save file.

Explanation: Either there is no room on the disk to save the parameter
file, or the file already exists and cannot be erased. Normanlly, when
you use an existing file name to save new parameters, the Performance
Facility over-writes the file on the disk. However, if the existing file is
either damaged or write-protected, the save parameter function fails.

Action: First, determine whether the file you wish to use is
write-protected.
If so, you can either remove the write-protect from the file, or enter a new
file name.

If the error occurs again, it is likely that your disk is full. Return to
DOS and erase files from the disk that are not needed.

When the problem is corrected, start the Trace and Performance program and
try the operation again.
******************************************************************
TITLE EAJPF112E Could not open performance file.

Explanation: The Performance Facility cannot be started because, either
there is no room on the disk to save the parameter file, or the file already
exists and cannot be erased.

Normally, when you use an existing performance file name to collect new
performance data, the Performance Facility overwrites the file on the
disk. However, if the existing file cannot be erased, usually because it
is write-protected, the Performance Facility cannot start.

Action: First, determine whether the file you wish to use is
write-protected.
If so, you can either remove the write-protect from the file, or enter a
new file name.

If the error occurs again, it is likely that your disk is full. Return to
DOS and erase files from the disk that are not needed.

When the problem is corrected, start the Trace and Performance program and
try the operation again.
******************************************************************
TITLE EAJPF120E Could not open synonym file.

Explanation: The synonym file was not found. Either the file name was
typed incorrectly, or the file does not exist.

Action: If the file name was typed incorrectly, enter it again and
continue.
Otherwise, press F2=DIR to display a list of the synonym files that are
on the
disk.
******************************************************************
TITLE EAJPF202E Starting time field is invalid.

Explanation: A start time was entered that is not valid. The start time
must be entered in this format:

hh:mm:ss

Where hh is hours, mm is minutes, and ss is seconds.

You must enter times on the basis of a 24-hour clock.

Action: Enter the start time again and continue.
******************************************************************
TITLE EAJPF203E Stopping time field is invalid.

Explanation: A stop time was entered that is not valid. The stop time
must be entered in this format:

hh:mm:ss

Where hh is hours, mm is minutes, and ss is seconds.

You must enter times on the basis of a 24-hour clock.

Action: Enter the stop time again and continue.
******************************************************************
TITLE EAJPF206E Open adapter failed, Code=xx, Bringup error=xxxx.

TAP.LAN from PCINFO

******************************************************************
TITLE EAJLF114E Could not find the parameter file.

Explanation: The parameter file was not found. Either the file name
was typed
incorrectly, or the file does not exist.

Action: If the file name was typed incorrectly, enter it again and
continue.
Otherwise, press F2=DIR to display a list of the parameter files that are on
the disk.
******************************************************************
TITLE EAJLF116E Traffic file name must have an extension of LC*.

Explanation: A traffic file extension was entered that does not begin with
the letters lc. If the traffic file extension was changed, the file cannot
be used.

Action: If the file extension was entered incorrectly, enter it again and
continue. Otherwise, press F2=DIR to display a list of the synonym
files that
are on the disk.
******************************************************************
TITLE EAJLF120E Could not open the synonym file.

Explanation: The synonym file was not found. Either the file name was
typed
incorrectly, or the file does not exist.

Action: If the file name was typed incorrectly, enter it again and
continue.
Otherwise, press F2=DIR to display a list of the synonym files that are
on the
disk.
******************************************************************
TITLE EAJLF151E Traffic file is empty.

Explanation: A traffic file was specified that does not contian any traffic
data. The Traffic Matrix Facility was stopped before connection data was
captured.

Action: Either use a different traffic file, or start the Traffic Matrix
Facility again and allow the facility to operate long enough to capture
data.
******************************************************************
TITLE EAJLF216E All sort addresses are filled.

Explanation: An attempt was made to select more than 10 addresses from
a synonym file. Only 10 addresses can be selected.

Action: Do not select more than 10 addresses.
******************************************************************
TITLE EAJLF253E Could not open output file for writing.

Explanation: The specified file could not be opened for writing.

Action: Enter a different file name.
******************************************************************
TITLE EAJLF255E Could not open index file.

Explanation: Internal error.

Action: Call the IBM Support Center.
******************************************************************
TITLE EAJLF257E Starting time is not within required boundaries.

Explanation: Starting time must be between start hour and start hour plus
duration minus 1.

For example, if a start hour of 10 and a duration of 3 are displayed on the
panel, the valid start hours are 10, 11 and 12.

Action: Enter a valid start hour.
******************************************************************
TITLE EAJLF258E Duration is not within required boundaries.

Explanation: The value entered in the duration field on the set search
duration panel is not valid. The value is either is not a number, is 0,
or it exceeds the total duration of the file.

For example, if a start hour of 10 and a duration of 3 is displayed on
the panel, you can enter a start time 11 and a duration of 2, or a start
time of 12 and a duration of 1.

Action: Enter a valid duration.
******************************************************************
TITLE EAJLF271E Could not open temporary file.

Explanation: Internal error.

Action: Call the IBM Support Center.
******************************************************************
TITLE EAJLF272E File pointer error.

Explanation: Interal error.

Action: Call the IBM Support Center.
******************************************************************
TITLE EAJLF300E File name may not be CON.

Explanation: An attempt was made to create a file named "CON". CON
cannot be
used as a file name.

Action: Enter a different file name.
******************************************************************
TITLE EAJLF909E Memory Allocation Failure.

Explanation: There is not enough memory for the Traffic Matrix Analysis
Facility.

Action: Return to DOS, stop all terminate/stay resident programs, and
remove them from DOS memory. Start the Traffic Matrix Analysis Facility
agian; if more memory is needed, start the Traffic Matrix Analysis Facility
using the LCAF command (do not type in TAP). See Appendix D,"Using Commands
to Start the Trace and Performance Facilities" on page D-1 of your IBM
Token-
Ring Network 16/4 Trace and Performance Program User's Guide, for more
information.
******************************************************************
TITLE EAJPR002E Invalid source address or synonym.

Explanation: You specified a parameter file that contains either an adapter
address that is not valid, or a synonym that is not recognized.

Action: Return to DOS and edit the parameter file to correct or delete the
name, or do not use the parameter file.

Make sure that all adapter addresses in the file consist of valid
hexadecimal
characters.

If synonyms are used in the parameter file, make sure that a synonym
file has
been specified that defines these synonyms.

Because synonym file names are not saved in parameter file, you must specify
a synonym file before you specify a parameter file that contains synonym.
******************************************************************
TITLE EAJPR080E Unrecognized parameter type.

Explanation: A parameter file was specified that contains a parameter type
that is not valid.

Action: To correct the parameter, return to DOS and edit the parameter
file.
Start the Trace and Performance program and try the operation again.
******************************************************************
TITLE EAJPR081E Invalid parameter value.

Explanation: A parameter file was specified that contains a parameter value
that is not valid for its type.

Action: To correct the parameter, return to DOS to edit the parameter
file and
delete the file extension. Start the Trace and Performance program and try
the operation again.
******************************************************************
TITLE EAJPR083E Extension not allowed on file name.

Explanation: A parameter file was specified that contains a file name and a
file extension. File extensions are not allowed in the parameter file.

Action: Retrun to DOS to edit the parameter file and delete the file
extension. Start the Trace and Performance program and try the operation
again.
******************************************************************
TITLE EAJPR084E Too many distribution intervals.

Explanation: A parameter file was specified that contains more than 10
distribution intervals. Only 10 distribution intervals are allowed.

Action: Return to DOS to edit and correct the file. Start the Trace and
Performance program and try the operation again.
******************************************************************
TITLE EAJPR085E Too many destination addresses or value too long.

Explanation: A parameter file was specified that either contains a
destination address or synonym that is too long, or contains more than
10 destination addresses.

The value in a distination address field cannot be more than 16 characters
in length, and only 10 destination addresses are allowed.

Action: Return to DOS to edit the file and delete extra addresses, or
correct an address field. Start the Trace and Performance program and try
the operation again.
******************************************************************
TITLE EAJPR086E Too many source addresses or value too long.

Explanation: A parameter file was specified that either contains a source
address or synonym that is too long, or contains more than 10 destination
addresses.

The value in a source address field cannot be more than 16 characters in
length, and only 10 source addresses are allowed.

Action: Retrun to DOS to edit the file and delete extra addresses, or
correct an address field. Start the Trace and Performance program and try
the operation again.
******************************************************************
TITLE EAJPR087E Start pattern not valid.

Explanation: A parameter file was specified that contains a start pattern
that is not valid. The start pattern must be a hexadecimal value and can be
up to 8 bytes long.

Action: Return to DOS to edit the file and correct the start pattern.
Start
the Trace and Performance program and try the operation again.
******************************************************************
TITLE EAJPR088E Invalid start trigger time.

Explanation: A parameter file was specified that contains a start time that
is not valid. The start trigger must be entered in this format:

hh:mm:ss

Where hh is hours, mm is minutes, and ss is seconds.

You must enter items on the basis of a 24-hour clock.

Action: Return to DOS to edit the file and correct the start trigger.
******************************************************************
TITLE EAJPR089E Invalid start trigger offset value.